Building Construction: "Framing Floor Joists and Walls" 1950 US Navy Training Film. more at http://hardware.quickfound.net/
"Illustrates procedures for constructing walls, floors, doors,and windows of a two-story building."
US Navy training film MN-5715b
NEW VERSION with improved video & sound: https://www.youtube.com/watch?v=hRdp-FqtJ4Y
Public domain film from the National Archives, slightly cropped to remove uneven edges, with the aspect ratio corrected, and mild video noise reduction applied.
The soundtrack was also processed with volume normalization, noise reduction, clipping reduction, and equalization.
Reupload of a previously uploaded film, in one piece instead of multiple parts.
Wall framing in house construction includes the vertical and horizontal members of exterior walls and interior partitions, both of bearing walls and non-bearing walls. These stick members, referred to as studs, wall plates and lintels (headers), serve as a nailing base for all covering material and support the upper floor platforms, which provide the lateral strength along a wall. The platforms may be the boxed structure of a ceiling and roof, or the ceiling and floor joists of the story above. The technique is variously referred to colloquially in the building trades as stick and frame, stick and platform, or stick and box as the sticks (studs) give the structure its vertical support, and the box shaped floor sections with joists contained within length-long post and lintels (more commonly called headers), supports the weight of whatever is above, including the next wall up and the roof above the top story. The platform also provides the lateral support against wind and holds the stick walls true and square. Any lower platform supports the weight of the platforms and walls above the level of its component headers and joists.
Framing lumber should be grade-stamped, and have a moisture content not exceeding 19%.
There are three historically common methods of framing a house.
- Post and Beam, which is now used predominately in barn construction.
- Balloon framing using a technique suspending floors from the walls was common until the late 1940s, but since that time, platform framing has become the predominant form of house construction.
- Platform framing often forms wall sections horizontally on the sub-floor prior to erection, easing positioning of studs and increasing accuracy while cutting the necessary manpower. The top and bottom plates are end-nailed to each stud with two nails at least 3.25 in (83 mm) in length (16d or 16 penny nails). Studs are at least doubled (creating posts) at openings, the jack stud being cut to receive the lintels(headers) that are placed and end-nailed through the outer studs.
Wall sheathing, usually a plywood or other laminate, is usually applied to the framing prior to erection, thus eliminating the need to scaffold, and again increasing speed and cutting manpower needs and expenses. Some types of exterior sheathing, such as asphalt-impregnated fibreboard, plywood, oriented strand board and waferboard, will provide adequate bracing to resist lateral loads and keep the wall square. (Construction codes in most jurisdictions require a stiff plywood sheathing.) Others, such as rigid glass-fibre, asphalt-coated fibreboard, polystyrene or polyurethane board, will not. In this latter case, the wall should be reinforced with a diagonal wood or metal bracing inset into the studs. In jurisdictions subject to strong wind storms (hurricane countries, tornado alleys) local codes or state law will generally require both the diagonal wind braces and the stiff exterior sheathing regardless of the type and kind of outer weather resistant coverings.
A multiple-stud post made up of at least three studs, or the equivalent, is generally used at exterior corners and intersections to secure a good tie between adjoining walls and to provide nailing support for the interior finish and exterior sheathing. Corners and intersections, however, must be framed with at least two studs.
Nailing support for the edges of the ceiling is required at the junction of the wall and ceiling where partitions run parallel to the ceiling joists. This material is commonly referred to as 'dead wood' or backing.
Exterior wall studs
Wall framing in house construction includes the vertical and horizontal members of exterior walls and interior partitions. These members, referred to as studs, wall plates and lintels, serve as a nailing base for all covering material and support the upper floors, ceiling and roof.
Exterior wall studs are the vertical members to which the wall sheathing and cladding are attached. They are supported on a bottom plate or foundation sill and in turn support the top plate. Studs usually consist of 2 × 4 in (51 × 100 mm) or 2 × 6 in (51 × 150 mm) lumber and are commonly spaced at 16 in (410 mm) on centre...
Tags: Building Construction: "Framing Floor Joists and Walls" 1950 US Navy Training Film, education, educational, documentary, history, film, Construction, framing, floor, Framing (construction), joist, wall, house building, Framing Floor Joists and Walls, home building, house construction, building construction, stud wall, how to, training, training film, navy training film, United States Navy, House-building, Design, build, building, door, window, nail, nailing, saw, cut, fit, US Navy, primer, basic, instruction, DIY, do it yourself, intro, introduction